Weller DEC1001 Manuel d'utilisateur télécharger pdf

MODEL DEC1001 ELECTROSTATIC DISSIPATIVE SOLDERING STATION

The DEC1001 Soldering Station offers the ultimate in

controlled temperature hand soldering tools for

production and repair facilities at the lowest possible

cost. The DEC1001 combines two complete and

separate control units in one housing to minimize

required bench space. The user has the option of using

EC1201A or EC1503A 40 watt tools, EC1302A 20 watt

tools, EC1204AP or EC1504AP 54 watt tools, or any two

of the five. These tools are all designed to be used

interchangeably without adversely affecting the tip

temperature calibration; and a wide variety of tip styles

are available for each tool. See insert for available tip

styles.

Tip temperature is electronically controlled throughout the temperature range of 350°F to 850°F (175°C to 455°C). The units

are calibrated to within ±10°F (±6°C) and tip temperature control is maintained within specification over line voltage

variations of ±10% and an ambient temperature range of 60°F to 110°F 16°C to 43°C).

Dynamic response to soldering load variation is insured by the use of a rapid response platinum sensor and full proportional

heater control. The sensor is positioned deep inside the solid copper, iron plated tip to insure quick response.

WARNING: This product, when used for soldering and similar applications, produces chemicals known to the

State of California to cause cancer and birth defects or other reproductive harm.

The electronic circuitry features a custom integrated circuit to give precise tip temperature control. The heater power is

controlled by a zero voltage circuit in the IC, which drives a thyristor to ensure that no switching transients are present on

the tip. In addition, the power unit is isolated from the AC line by a transformer and only 24VAC is used to drive the heating

element. The soldering tip is grounded through the power units three wire line cord. These features combine with the

calibrated temperature control to give the ultimate in safety for sensitive hand soldering.

The Weller

ESD soldering stations carry the science of hand soldering one level higher. These stations also have complete

freedom from stored static charges. The blue plastic used in this product meets the requirements for ELECTROSTATIC

PROTECTIVE MATERIALS as required in MIL-B-81705. The blue plastic material passes STATIC DECAY test per Federal

Test Method Standard Number 101, and SURFACE RESISTIVITY tests per ASTM-D257. The station housing and hand

piece are grounded with a separate conductor that terminates at the third pin on the power cord. All Weller

ESD tools

comply with DOD-HDBK-263.

The Weller

DEC1001 units are UL listed and meet DOD-STD-2000, MIL-S-2000, MIL-S-45743, W-S-6536, W-S-570 and

DOD-STD-1686.

DEC1001 OPERATING INSTRUCTIONS

Unpack unit carefully. Select appropriate spring and funnel for tool to be used and place in slot in top of tool stand. Attach

tool stands to either side of power unit, if desired. Fill reservoir with water and wet sponge, distilled water is recommended.

Insert tool in holder and connect tool plug to receptacle on power unit; rotate plug housing to lock plug into receptacle.

Insert line cord plug into properly grounded AC receptacle and turn unit on. Set temperature control knob to desired tip

temperature (approach desired temperature by turning CCW). Wait 30 seconds. Remove tool from holder and tin tip with

solder. Unit is now ready for use.

1 2 3 4

Résumé du contenu

Page 1

MODEL DEC1001 ELECTROSTATIC DISSIPATIVE SOLDERING STATIONThe DEC1001 Soldering Station offers the ultimate incontrolled temperature hand soldering too

Page 2

Always use the lowest temperature that will handle the load you are soldering. The Weller® electronic control providesmaximum power to the heated load

Page 3

Fuse open - replace. Fuseholder located under base. Use 1.6 Amp Fuse (1 Amp 5x20mm fuse on 240VAC).Line cord open - replaceTransformer defective - rep

Page 4

CUSTOMER SERVICESShould your DEC1001 require repair or adjustment it may be sent to the following address:Cooper Tools - Weller Division1000 Lufkin Ro

Commentaires sur ces manuels

Pas de commentaire

Weller DEC1001 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Weller DEC1001. Weller DEC1001 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Weller DEC1001